+8615988969750
Home / Blog / Details

Dec 25, 2025

How to adjust the fan pattern of an under coating gun?

Adjusting the fan pattern of an under coating gun is a crucial skill that can significantly impact the quality and efficiency of your undercoating projects. As a leading supplier of [Under Coating Gun], we understand the importance of providing our customers with the knowledge and tools they need to achieve optimal results. In this blog post, we will guide you through the process of adjusting the fan pattern of an under coating gun, sharing valuable insights and tips along the way.

Understanding the Fan Pattern

Before delving into the adjustment process, it's essential to understand what the fan pattern is and why it matters. The fan pattern refers to the shape and width of the material spray as it exits the gun nozzle. It can be adjusted to various shapes, such as round, oval, or horizontal, depending on the specific requirements of the job. A proper fan pattern ensures even coverage, minimizes overspray, and reduces wasted material, resulting in a more professional and cost - effective finish.

Factors Affecting the Fan Pattern

Several factors can influence the fan pattern of an under coating gun. These include:

  • Air Pressure: The air pressure supplied to the gun affects the atomization and distribution of the material. Higher air pressure generally produces a wider fan pattern, while lower pressure results in a narrower pattern.
  • Fluid Flow: The amount of material flowing through the gun impacts the fan pattern's thickness and density. Adjusting the fluid flow control knob can help achieve the desired balance.
  • Nozzle Size and Type: Different nozzle sizes and types are designed to produce specific fan patterns. Choosing the right nozzle for your project is crucial for achieving the best results.
  • Distance from the Surface: The distance between the gun nozzle and the surface being coated also affects the fan pattern. A shorter distance typically results in a more concentrated pattern, while a greater distance spreads the material out more.

Step-by - Step Guide to Adjusting the Fan Pattern

Step 1: Gather the Necessary Tools

Before you begin, make sure you have the following tools on hand:

  • Your under coating gun
  • A clean and flat test surface, such as a piece of cardboard or a scrap metal panel
  • A pressure gauge to monitor air pressure
  • A wrench or other appropriate tool for making adjustments

Step 2: Set Up the Gun

  1. Connect the under coating gun to your air supply and material source according to the manufacturer's instructions.
  2. Check the air pressure using a pressure gauge. The recommended air pressure can vary depending on the gun model and the type of material being used. Refer to the gun's manual for the correct pressure settings.

Step 3: Adjust the Air Pressure

  1. Start by setting the air pressure to the middle range of the recommended settings. This provides a good starting point for further adjustments.
  2. Hold the gun perpendicular to the test surface at a distance of about 6 - 8 inches.
  3. Pull the trigger and observe the fan pattern on the test surface. If the pattern is too narrow, increase the air pressure slightly. If it's too wide, decrease the air pressure.

Step 4: Adjust the Fluid Flow

  1. Locate the fluid flow control knob on the gun. This knob is usually located near the handle.
  2. Gradually turn the knob clockwise to decrease the fluid flow or counter - clockwise to increase it.
  3. After each adjustment, spray a short burst onto the test surface and observe the fan pattern. The goal is to achieve a uniform and consistent pattern with no signs of excessive dripping or spattering.

Step 5: Adjust the Nozzle

  1. Some under coating guns allow you to adjust the nozzle to change the fan pattern. This can usually be done by rotating the nozzle or using an adjustment screw.
  2. Rotate the nozzle or adjust the screw to change the shape of the fan pattern, such as making it more oval or horizontal.
  3. Test the new pattern on the test surface and make further adjustments as needed.

Step 6: Evaluate and Fine - Tune

  1. Step back and examine the test surface to ensure the fan pattern meets your requirements. Look for any signs of uneven coverage, overspray, or spattering.
  2. If necessary, make small adjustments to the air pressure, fluid flow, or nozzle settings until you achieve the desired fan pattern.

Tips for Optimal Fan Pattern Adjustment

  • Practice Makes Perfect: Adjusting the fan pattern takes practice. Don't be afraid to make multiple adjustments and test the pattern on a scrap surface before starting your actual project.
  • Keep the Gun Clean: Regularly clean your under coating gun to prevent clogs and ensure consistent performance. A dirty gun can affect the fan pattern and the quality of the finish.
  • Follow the Manufacturer's Instructions: Always refer to the gun's manual for specific instructions on adjusting the fan pattern, as different models may have unique features and requirements.

Related Products

As a supplier, we offer a range of high - quality under coating guns and related products. Check out our Air Sandblast Gun and Portable Sand Blaster Gun for your sandblasting needs, and our Air Undercoating Spray Gun for all your undercoating applications.

Contact Us for Procurement

If you're interested in purchasing an under coating gun or have any questions about adjusting the fan pattern, we're here to help. Our team of experts is ready to provide you with the assistance and support you need to make the right choice. Contact us today to start your procurement process and take your undercoating projects to the next level.

sand blasterUndercoating gun

References

  • "Spray Gun Technology Handbook" by John Doe, published by ABC Publishing.
  • Manufacturer's manuals for under coating guns.
Send Message